|
|
| Author |
Message |
Robert or Karen Swarts
Guest
|
 Posted: Sat Jan 29, 2005 4:38 am Post subject: Mast foot problem |
 |
|
I have unstepped the mast on my Coronado 25 and noticed that the mast foot
is flat in the fore and aft direction, but the tabernacle is stepped down
about 1/16" at the middle of the footprint of the foot. Anyone know why this
is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts |
|
| Back to top |
|
 |
|
|
Steve Lusardi
Guest
|
| Posted: Sun Jan 30, 2005 2:52 am Post subject: Re: Mast foot problem |
|
|
Water drain?
Steve
"Robert or Karen Swarts" <ravensrest@olypen.com> wrote in message
news:10vlj9cj19d6r98@corp.supernews.com...
| Quote: | I have unstepped the mast on my Coronado 25 and noticed that the mast foot
is flat in the fore and aft direction, but the tabernacle is stepped down
about 1/16" at the middle of the footprint of the foot. Anyone know why
this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
|
|
| Back to top |
|
|
ddinc
Guest
|
| Posted: Sun Jan 30, 2005 6:26 am Post subject: Re: Mast foot problem |
|
|
I am not sure of your description, but we put a small rocker
on the bottom of the mast to prevent eccentricity in the tube.
(the mast does not sit quite flat on the bottom)
I am not sure I would worry about it, but I am not sure
what you are describing.
"Robert or Karen Swarts" <ravensrest@olypen.com> wrote in message
news:10vlj9cj19d6r98@corp.supernews.com...
| Quote: | I have unstepped the mast on my Coronado 25 and noticed that the mast foot
is flat in the fore and aft direction, but the tabernacle is stepped down
about 1/16" at the middle of the footprint of the foot. Anyone know why
this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
|
|
| Back to top |
|
|
Jim Conlin
Guest
|
| Posted: Sun Jan 30, 2005 7:37 am Post subject: Re: Mast foot problem |
|
|
Can't remember what kind of boat but i remember one builder/rigger who
deliberately cut the bottom of his mast tubes a liitle on the bias so
that the bottom panel of the mast was encouraged to bow forward under
compression.
Robert or Karen Swarts wrote:
| Quote: | I have unstepped the mast on my Coronado 25 and noticed that the mast foot
is flat in the fore and aft direction, but the tabernacle is stepped down
about 1/16" at the middle of the footprint of the foot. Anyone know why this
is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
|
|
| Back to top |
|
|
Robert or Karen Swarts
Guest
|
| Posted: Sun Jan 30, 2005 10:49 pm Post subject: Re: Mast foot problem |
|
|
The bottom of the mast foot is flat, but if you drew a line in the fore and
aft direction along the center of the tabernacle, it would step downwards
about 1/16" halfway along. Why would anyone design a mast/foot/tabernacle to
rest on only the aft half of the foot? I have come up with no good reason
thus far.
BS
"Jim Conlin" <conlin@comcast.net> wrote in message
news:vOOdnVfPSp1v2mHcRVn-pQ@comcast.com...
| Quote: | Can't remember what kind of boat but i remember one builder/rigger who
deliberately cut the bottom of his mast tubes a liitle on the bias so that
the bottom panel of the mast was encouraged to bow forward under
compression.
Robert or Karen Swarts wrote:
I have unstepped the mast on my Coronado 25 and noticed that the mast foot
is flat in the fore and aft direction, but the tabernacle is stepped down
about 1/16" at the middle of the footprint of the foot. Anyone know why
this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
|
|
| Back to top |
|
|
ddinc
Guest
|
| Posted: Mon Jan 31, 2005 4:12 am Post subject: Re: Mast foot problem |
|
|
Can you define a tabernackle?
Mast step?
"Robert or Karen Swarts" <ravensrest@olypen.com> wrote in message
news:10vq7r2n2c2iv85@corp.supernews.com...
| Quote: | The bottom of the mast foot is flat, but if you drew a line in the fore
and aft direction along the center of the tabernacle, it would step
downwards about 1/16" halfway along. Why would anyone design a
mast/foot/tabernacle to rest on only the aft half of the foot? I have come
up with no good reason thus far.
BS
"Jim Conlin" <conlin@comcast.net> wrote in message
news:vOOdnVfPSp1v2mHcRVn-pQ@comcast.com...
Can't remember what kind of boat but i remember one builder/rigger who
deliberately cut the bottom of his mast tubes a liitle on the bias so
that the bottom panel of the mast was encouraged to bow forward under
compression.
Robert or Karen Swarts wrote:
I have unstepped the mast on my Coronado 25 and noticed that the mast
foot is flat in the fore and aft direction, but the tabernacle is stepped
down about 1/16" at the middle of the footprint of the foot. Anyone know
why this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
|
|
| Back to top |
|
|
Robert or Karen Swarts
Guest
|
| Posted: Mon Jan 31, 2005 4:20 am Post subject: Re: Mast foot problem |
|
|
Yes. In this case, the cast aluminum fitting on which the mast foot hinges
by means of a single pin, and on which the mast rests when it is stepped.
BS
"ddinc" <dobroth@erols.com> wrote in message
news:W6idnSXo8oac92DcRVn-2Q@rcn.net...
| Quote: | Can you define a tabernackle?
Mast step?
"Robert or Karen Swarts" <ravensrest@olypen.com> wrote in message
news:10vq7r2n2c2iv85@corp.supernews.com...
The bottom of the mast foot is flat, but if you drew a line in the fore
and aft direction along the center of the tabernacle, it would step
downwards about 1/16" halfway along. Why would anyone design a
mast/foot/tabernacle to rest on only the aft half of the foot? I have
come up with no good reason thus far.
BS
"Jim Conlin" <conlin@comcast.net> wrote in message
news:vOOdnVfPSp1v2mHcRVn-pQ@comcast.com...
Can't remember what kind of boat but i remember one builder/rigger who
deliberately cut the bottom of his mast tubes a liitle on the bias so
that the bottom panel of the mast was encouraged to bow forward under
compression.
Robert or Karen Swarts wrote:
I have unstepped the mast on my Coronado 25 and noticed that the mast
foot is flat in the fore and aft direction, but the tabernacle is
stepped down about 1/16" at the middle of the footprint of the foot.
Anyone know why this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
|
|
| Back to top |
|
|
Maynard G. Krebbs
Guest
|
| Posted: Mon Jan 31, 2005 6:42 am Post subject: Re: Mast foot problem |
|
|
On Sun, 30 Jan 2005 15:20:04 -0800, "Robert or Karen Swarts"
<ravensrest@olypen.com> wrote:
| Quote: | Yes. In this case, the cast aluminum fitting on which the mast foot hinges
by means of a single pin, and on which the mast rests when it is stepped.
BS
|
It wouldn't be for clearance when the mast is pivoted on the pin/bolt?
Mark E. Williams |
|
| Back to top |
|
|
Terry Spragg
Guest
|
| Posted: Mon Jan 31, 2005 9:04 am Post subject: Re: Mast foot problem |
|
|
Robert or Karen Swarts wrote:
| Quote: | I have unstepped the mast on my Coronado 25 and noticed that the mast foot
is flat in the fore and aft direction, but the tabernacle is stepped down
about 1/16" at the middle of the footprint of the foot. Anyone know why this
is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
|
Some sort of hinge arrangement to make starting the mast down a
little easier?
Which way is the drop?
There was a corner ground off of the foot on my 22' SC to make it
easier to hinge.
Terry K |
|
| Back to top |
|
|
Robert or Karen Swarts
Guest
|
| Posted: Mon Jan 31, 2005 9:53 pm Post subject: Re: Mast foot problem |
|
|
All of your responses are plausible, but I don't think any of them are
correct. The drop is 1/16" down as one moves forward along the tabernacle.
The foot itself is rebated in the middle to ensure good contact on the edges
and to shed water. The hinge, which is at the rear, requires no clearance. I
just don't know.
BS
"Terry Spragg" <tspragg567nospam@rogers.com> wrote in message
news:rqKdnZF-iMjgM2DcRVn-pA@rogers.com...
| Quote: | Robert or Karen Swarts wrote:
I have unstepped the mast on my Coronado 25 and noticed that the mast
foot is flat in the fore and aft direction, but the tabernacle is stepped
down about 1/16" at the middle of the footprint of the foot. Anyone know
why this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the tabernacle? Any
suggestions would be welcome.
Bob Swarts
Some sort of hinge arrangement to make starting the mast down a little
easier?
Which way is the drop?
There was a corner ground off of the foot on my 22' SC to make it easier
to hinge.
Terry K
|
|
|
| Back to top |
|
|
wtf
Guest
|
| Posted: Tue Feb 01, 2005 5:22 am Post subject: Re: Mast foot problem |
|
|
Robert or Karen Swarts wrote:
| Quote: | All of your responses are plausible, but I don't think any of them
are
correct. The drop is 1/16" down as one moves forward along the
tabernacle.
The foot itself is rebated in the middle to ensure good contact on
the edges
and to shed water. The hinge, which is at the rear, requires no
clearance. I
just don't know.
BS
"Terry Spragg" <tspragg567nospam@rogers.com> wrote in message
news:rqKdnZF-iMjgM2DcRVn-pA@rogers.com...
Robert or Karen Swarts wrote:
I have unstepped the mast on my Coronado 25 and noticed that the
mast
foot is flat in the fore and aft direction, but the tabernacle is
stepped
down about 1/16" at the middle of the footprint of the foot.
Anyone know
why this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the
tabernacle? Any
suggestions would be welcome.
Bob Swarts
Some sort of hinge arrangement to make starting the mast down a
little
easier?
Which way is the drop?
There was a corner ground off of the foot on my 22' SC to make it
easier
to hinge.
Terry K
|
I think you all may be over thinking it. As an occassional builder, the
first thing I thought was, the builder did not have a big enough piece
of scrap, so he used two small pieces  ..
Well, it's a thought!
umph... |
|
| Back to top |
|
|
Robert or Karen Swarts
Guest
|
| Posted: Tue Feb 01, 2005 10:43 pm Post subject: Re: Mast foot problem |
|
|
Good idea, but in this case the tabernacle is a casting that Columbia Boats
put on several thousand Coronado 25s.
BS
"wtf" <skcusemans@eudoramail.com> wrote in message
news:1107217353.749069.41800@c13g2000cwb.googlegroups.com...
| Quote: |
Robert or Karen Swarts wrote:
All of your responses are plausible, but I don't think any of them
are
correct. The drop is 1/16" down as one moves forward along the
tabernacle.
The foot itself is rebated in the middle to ensure good contact on
the edges
and to shed water. The hinge, which is at the rear, requires no
clearance. I
just don't know.
BS
"Terry Spragg" <tspragg567nospam@rogers.com> wrote in message
news:rqKdnZF-iMjgM2DcRVn-pA@rogers.com...
Robert or Karen Swarts wrote:
I have unstepped the mast on my Coronado 25 and noticed that the
mast
foot is flat in the fore and aft direction, but the tabernacle is
stepped
down about 1/16" at the middle of the footprint of the foot.
Anyone know
why this is? Was there originally a spacer of
some sort between the forward bottom of the foot and the
tabernacle? Any
suggestions would be welcome.
Bob Swarts
Some sort of hinge arrangement to make starting the mast down a
little
easier?
Which way is the drop?
There was a corner ground off of the foot on my 22' SC to make it
easier
to hinge.
Terry K
I think you all may be over thinking it. As an occassional builder, the
first thing I thought was, the builder did not have a big enough piece
of scrap, so he used two small pieces ..
Well, it's a thought!
umph...
|
|
|
| Back to top |
|
|
|
Search
Register
Log in to check your private messages
Profile
Log in
FAQ
Memberlist
Usergroups